Steel gear set in an industrial drive, illustrating the straight parallel teeth of spur gears and their mesh

A spur gear is a cylindrical gear with straight teeth that transmits motion between parallel shafts, and its design reduces to three numbers: module (pitch diameter divided by tooth count), tooth count and pressure angle — 20 degrees being the modern default. Those three define the basic tooth geometry; undercut margin, profile shift, contact ratio, backlash, accuracy grade and inspection method still have to be specified or checked separately against published gear standards.

This guide covers the geometry that governs a pair, the two limits most designs run into, how tooth accuracy is specified and measured, what the failure modes point at, and where metal injection molding fits against hobbing and powder metallurgy.

Spur Gear Geometry in Seven Numbers

Metric gear geometry is compact. Module is pitch diameter divided by tooth count, so d = m·z and the pair relationship is centre distance a = m(z₁ + z₂)/2 with ratio i = z₂/z₁. Conventional mating spur gears normally use the same module and pressure angle: module sets tooth size, pressure angle sets flank slope, and neither can be traded against the other once the pair is fixed.

ParameterSymbolStandard full-depth spur gear
Modulemm = d / z, in millimetres
Pitch diameterdd = m·z
Addendumh_aabout 1.0 m
Dedendumh_fabout 1.25 m
Whole depthhabout 2.25 m
Base diameterd_bd·cos α
Base pitchp_bπ·m·cos α
Centre distance, pairam(z1 + z2) / 2
Circular tooth thicknesssabout π·m/2 at the pitch circle

Base pitch p_b = π·m·cos α, not circular pitch, controls how much of the mesh is in contact at any instant. In the inch world the same geometry is written as diametral pitch, roughly 25.4 divided by the module.

Tooth Count: Undercut, Profile Shift and Contact Ratio

Undercut is the first limit most designs meet: the generating action removes material near the root and thins the most highly stressed section. The theoretical no-undercut count is z_min = 2/sin²α, roughly 32 teeth at 14.5 degrees, 17 at 20 degrees and 11 at 25 degrees. For a conventional 20-degree full-depth gear, 18 teeth is often treated as a practical working minimum — a useful rule for one geometry, not a universal limit.

Undercut is avoidable without changing tooth count. Positive profile shift moves the cutter outward and thickens the root; a larger pressure angle raises the limit but increases radial separating force on bearings and housing; stub teeth trade contact ratio for root clearance. Each fix costs something, so the trade has to be calculated rather than assumed.

Contact ratio is the length of action divided by base pitch, or how many tooth pairs share load on average. Continuous conjugate action needs more than 1.0, design guidance commonly targets about 1.2, and standard spur pairs often land between 1.4 and 1.7. Tooth thickness closes the geometry: about π·m/2 at the pitch circle, s_p = m(π/2 + 2x·tan α) with profile shift. Backlash is deliberate thinning of both teeth, specified as a range at a stated centre distance and temperature.

Accuracy Grades and Tooth Thickness Inspection

Gear accuracy is a system, not a single number. ISO 1328 numbers accuracy grades from 1 to 12 in decreasing precision, but the numbering and its application depend on the standard part and edition used — the 1975 edition, its later parts and the AGMA systems differ, so the applicable standard, part and edition must be named on the drawing along with the grade and reference diameter range. A complete callout also states the characteristics controlled: pitch error, profile error, lead error, runout and the tooth thickness or backlash requirement.

Tooth thickness is verified by span measurement across a defined number of teeth, measurement over pins or balls, chordal thickness, or a gear measuring centre. Over-pin values are functional drawing dimensions only when tooth count, pin diameter, datum and measuring conditions are defined; the result shifts with pin diameter, pressure angle, profile shift and runout, so it cannot replace circular tooth thickness casually.

For molded gears, measure tooth thickness rather than outside diameter. Outside diameter follows the addendum and moves with tool wear and shrinkage compensation, while the functional dimension is the flank position the mating gear sees. Control span at a fixed tooth count at maximum material, then check backlash functionally. The honest limitation is that as-sintered error is distributed rather than a size offset: dimensions land within ±0.3–0.5% of nominal, but cumulative pitch error and runout are set by shrinkage, distortion, density gradients and furnace support, which one dimension cannot capture.

Materials and Heat Treatment for Loaded Teeth

Carburizing and carbonitriding produce a hard case over a tougher core and remain the standard route for loaded steel gears; through-hardening is simpler but gives a less favourable surface-to-core combination, and nitriding offers low distortion with a shallower case and strong dependence on alloy and process control. Case depth, core hardness and root fillet geometry matter more than the alloy name on the certificate.

Stainless behaves differently. Austenitic 316L and 304 cannot be hardened by heat treatment, so wear resistance comes from the alloy, cold work or surface treatment rather than a martensitic case; 420 and 440C do respond to hardening and are the usual stainless choice where corrosion resistance and tooth hardness are both needed. Emitech molds 316L, 304, 17-4PH, 420 and 430L stainless, 4605, 8620 and 4340 low-alloy steels, plus Ti-6Al-4V, soft-magnetic Fe-Ni, Kovar ASTM F15 and cobalt-chromium ASTM F75 — per-alloy detail is in the MIM materials guide.

Failure Modes and What They Point At

Spur gear failures are diagnostic because each mode starts in a different place on the tooth, so reading the surface identifies which design variable was wrong.

  • Root bending fatigue: crack at the fillet running across the root, from overload, an undersized fillet or an undercut root; fix the geometry, not just the hardness.
  • Pitting and micropitting: craters near the pitch line from contact fatigue, driven by contact stress, lubricant film and finish.
  • Scuffing: smeared, torn flanks from metal-to-metal contact at high sliding speed; look at lubricant and running-in first.
  • Wear with growing backlash: slow flank loss from abrasive contamination, followed by impact loading.
  • One-sided wear or a band along the face: alignment and mounting error, since load never reached the rest of the face width.

Residual porosity belongs on this list for any powder route. Sintered and molded gears reach 95–99% of theoretical density, and the remainder reduces ductility and fatigue resistance relative to wrought stock, most visibly at the root fillet. For fatigue-critical gearing, qualify the material condition against certified test data and avoid reading a density figure as a strength guarantee.

Manufacturing Routes: Hobbing, Powder Metallurgy and MIM

Hobbing and shaping generate the tooth form from solid stock, and grinding afterwards turns a cut gear into a precision one. The route handles any module and corrected profile, with unit cost driven by cycle time and finishing — still the right answer for prototypes, low volumes, large diameters and tight flank grades.

Powder metallurgy presses a near-net gear and sinters it: excellent for high-volume simple gears where the die amortizes, with porosity limiting ductility and bending fatigue. Metal injection molding sits at the high-complexity end — fine powder and binder are injected, debound and sintered to 95–99% of theoretical density, so hubs, keyways, bores and lightening features form with the teeth in one cycle instead of in additional setups.

RouteBest fitTooth accuracy realityWhere it fails
Hobbed or shaped, then groundAny module and tooth count, prototypes to large batchesCutting gives commercial grades; grinding sets the precision gradeCost scales with finishing time; hard finishing adds lead time
Powder metallurgy, die compactionHigh-volume gears of simple shape sized for the dieSizing improves dimensions, not flank geometryPorosity limits ductility and bending fatigue; die amortization needs volume
Metal injection moldingSmall, complex, high-volume gears with hubs and bores molded inAs-sintered ±0.3–0.5% of nominal; about ±0.01 mm on sized or ground featuresNo precision flank grade as-sintered; not for large diameter or high torque

The molding window for spur gears is narrow and worth stating precisely. Published application ranges put common molded gear modules at roughly 0.3 to 1.5 with part masses of 0.1–200 g and walls of 0.5–6 mm; as-sintered tolerances are ±0.3–0.5% of nominal (about ±0.025 mm on features under 3 mm), tightening to approximately ±0.01 mm only on features sized, coined or ground afterwards. Emitech runs 17 injection machines, 13 debinding furnaces and 22 sintering furnaces (4 continuous, 18 vacuum), with 24 sizing and 14 grinding machines for that post-sinter work — see MIM capabilities.

Design rules are mostly about heat extraction and ejection: give the root fillet the largest radius the mate's tip clearance allows, keep face width consistent with the hub, thin webs rather than leaving solid discs that cannot be fed during shrinkage, and design bore and hub around the ejector and core. Teeth molded in one plane release axially, so the flanks usually need no draft; problems appear at the ends, where sharp tooth tips, thin rims and deep narrow tooth spaces cool and eject badly.

The limitations deserve equal space. As-sintered molded teeth are not recommended where a precision ISO or AGMA flank grade is the acceptance criterion, because cumulative pitch error and runout from sintering must be corrected by grinding or not at all; and MIM is not suitable for large-diameter, coarse-module or high-torque gears, where tool size, press capacity and distortion over section all work against the process. A molded gear running against a cut mate is a realistic, often economical combination; a molded gear specified to hold a ground gear's accuracy as-sintered is not.

Frequently Asked Questions

Q: How do I choose the module for a spur gear?

Start from transmitted torque and allowable tooth bending stress with a margin for shock, confirm contact stress separately, then check tooth count against the undercut limit and contact ratio before locking the pair. Standard module series exist so cutters and mating parts stay interchangeable; the exact selection for a given duty cycle is a calculation, and a moldable version is quoted on request.

Q: At what tooth count does a 20-degree spur gear undercut?

About 17 teeth is the theoretical limit for a conventional 20-degree full-depth involute gear, and 18 is often used as a practical working minimum. Below that undercut is not automatic: positive profile shift, a larger pressure angle, stub teeth or different cutter geometry can make fewer teeth workable, at a cost in contact ratio, interference margin or separating force.

Q: What tooth accuracy can a MIM spur gear hold as-sintered?

As-sintered dimensions land within ±0.3–0.5% of nominal, about ±0.025 mm on features under 3 mm, and sized or ground features reach approximately ±0.01 mm. That is not a flank accuracy grade: pitch error and runout follow shrinkage, distortion and furnace support, so a precision ISO or AGMA grade as-sintered is not recommended and must be demonstrated on sample parts. Where a tight grade is the acceptance criterion, plan on grinding or choose a cut gear.

Q: How should tooth thickness be measured on a molded gear?

By span measurement across a defined number of teeth, or measurement over pins, with tooth count, pin diameter, datum and measuring conditions stated on the drawing. Outside diameter is not a substitute, since it follows addendum and tool wear rather than the flank position that sets backlash. Specify span at maximum material and verify backlash functionally at the operating centre distance.

Q: Is MIM suitable for high-torque power transmission gears?

Usually not. MIM suits small, complex, high-volume gears within roughly 0.1–200 g and modules around 0.3–1.5, where shape complexity pays for the tool. Large-diameter, coarse-module and high-torque gears run into tool size, press capacity, distortion over section and residual porosity at the root fillet; for those duties a cut and ground gear is the more reliable route.

A spur gear is defined by module, tooth count and pressure angle; undercut margin, contact ratio, backlash, accuracy grade and inspection method all follow from those three plus the duty cycle. Specifying them explicitly, with the standard edition and measurement method named, prevents most disputes that surface at first article.

If the gear is small, geometrically complex and needed in volume, a molded version is worth pricing against cutting: send the drawing and duty cycle and Emitech reviews it for MIM suitability, returning a recommendation and quotation within 24 hours through the contact page. Related reading: MIM small gears, the MIM gears manufacturing guide, ring gear geometry for internal teeth, and MIM tolerances for how the dimensional window is held.

Precision Metal Parts from Emitech

Nanjing Emitech delivers MIM, CNC machining, and custom metal parts. MIM services · Request a quote