MIM part marking splits by information type, not by preference. Fixed information — logos, orientation arrows, part numbers, cavity identifiers — is best formed during injection molding by engraved or raised cavity geometry, while variable data such as lot codes, serial numbers, and 2D codes is best applied by laser after sintering. Neither route is automatically permanent, and both have to be validated on production-equivalent parts rather than on a polished coupon.
The split is structural. A molded-in mark is part of the geometry, so it survives every later operation but cannot change without touching the tool; a laser mark is added at the end of the route, so it carries variable data and late changes but depends on surface condition and parameters. This page covers how each route is designed, how molded lettering is scaled for sintering shrinkage, what laser depth actually removes, and how to write a marking requirement that can be inspected.
Two Routes, One Decision: Molded-In or Laser-Marked
Molded-in marking is formed during injection molding, usually through engraved or raised lettering inserted into the cavity. It is not a post-process: the mark exists as soon as the green part is ejected and passes through debinding and sintering with the part. Laser marking is applied after sintering, usually after finishing, and writes the mark with a focused beam that discolors, ablates, or engraves the surface depending on alloy and parameters.
| Dimension | Molded-in text or symbol | Laser marking or engraving |
|---|---|---|
| Information type | Fixed text, arrows, orientation marks, logos, cavity or part IDs | Variable lot, serial, date, calibration and device-specific data |
| Timing | Designed into the mold; present after molding and sintering | Applied after sintering, usually after finishing |
| Tooling impact | Cavity inserts, lettering geometry, draft, ejection review, shrinkage scaling | Laser equipment, fixturing, parameter development, debris control |
| Change flexibility | Low; a text change can mean an insert or mold revision | High; layouts and data change in software |
| Failure modes | Underfill, chipped strokes, flash at the mark, residue in deep text | Low contrast, shallow removal, oxide or recast at the mark, poor code grading |
The practical split follows from the table. Information that never changes for the life of the tool can be molded in and removed from the operation list; information that changes per lot, per unit, or per revision belongs in laser software rather than in tool steel. Parts needing both carry a molded logo plus a laser-marked data field, with the laser field kept off sealing and wear surfaces.
Molded-In Text: What the Tool Can Carry
A molded-in mark is a small feature with its own molding physics. Recessed text needs cavity steel that can be cut or inserted without chipping at the stroke edges, and raised text needs enough surrounding land to survive ejection. Both need draft or a polished wall so the green body releases, an aspect ratio the filled feedstock can fill before the gate freezes, and a location away from edges where powder-flow disturbance shows as a short or a splay mark.
Three rules matter more than any nominal dimension. First, text belongs on a face that is neither a sealing surface nor a mating datum, and away from the parting line, gate mark, and ejector pin footprints — the same witness features used to identify MIM parts are exactly the features that will sit on top of a poorly placed mark. Second, thin-stroke lettering in a thick section creates a local flow restriction, so stroke width and character height have to be judged together rather than separately. Third, small, deep text cavities trap powder and binder residue and are hard to clean between runs.
Shrinkage is where molded marking earns its reputation for surprises. Lettering is scaled with the cavity by the measured shrinkage factor for that feedstock and sintering cycle, so character height, stroke width, and spacing all move together. If the factor is off, the mark is off by the same proportion as the part's critical dimensions; if shrinkage is anisotropic, glyphs distort in one direction relative to the other. Mark geometry is therefore cut from a validated factor and checked on sintered parts — the method itself lives on the MIM shrinkage compensation page, and practical minimum character height and stroke width for a given part and alloy are quoted on request after a tool trial.
Laser Marking After Sintering: Depth and Heat Effects
Laser marking covers a spectrum rather than a single process. At one end, an annealing or discoloration mark changes the oxide state at the surface with essentially no material removal. At the other, engraving removes metal, and cited industry practice commonly specifies engraved mark depths in the approximate range of 0.01 mm to 0.10 mm, with the depth driven by the required durability rather than by a default setting. Deeper removal is not a free upgrade: it reduces remaining section thickness, creates a stress concentration at the mark boundary, can retain contaminants, and may affect corrosion resistance or fatigue performance, so it has to be validated for the specific alloy and duty cycle.
The heat-affected zone matters on MIM parts because the part is already near-net shape and often thin. Laser processing can leave recast material, oxide films, debris, and residual stress around the mark, and on stainless grades that means the passive film at the mark differs from the film on the surrounding surface. Whether that matters depends on the environment: a cosmetic mark on a housing is a different problem from a serial number in a wet, cleaned, or sterilized duty cycle. Alloy choice shifts the response too — 316L, hardened 17-4PH, and Ti-6Al-4V behave differently under the same nominal parameters.
Sequence is part of the design. Marking before passivation exposes a fresh, possibly oxide-free surface to the acid bath; marking after passivation leaves the mark without the surrounding passive layer. Heat treatment in between can change the substrate under the mark. The route therefore has to be defined as a whole — sinter, heat treat, finish, mark, passivate or clean — and the marking step placed where its effect on the surface is acceptable. Post-sinter finishing options and the surfaces they produce are covered on the surface finish page.
Readability and Validation on Real Surfaces
Contrast is a surface property, not a laser setting. The readable quality of a mark depends on roughness, porosity, oxide condition, passivation state, coating, curvature, and residual contamination, so the same parameters can produce a crisp mark on one lot and a marginal one on the next. This is especially relevant to MIM, where as-sintered surfaces are typically rougher than polished, tumbled, blasted, or coated surfaces, and where residual porosity scatters light differently from a fully dense wrought surface.
A dark mark is not automatically a machine-readable code. Print-quality grading, symbol contrast, cell size, quiet zones, and scanner performance all have to hold after the mark has been through the cleaning, passivation, or sterilization steps the part will actually see. Validation is therefore done on production-equivalent parts — same alloy, sintering condition, surface finish, mark parameters, geometry, and post-mark cleaning cycle. A code that scans on a flat polished coupon establishes nothing about the production part, and a single successful scan is an observation rather than a validation.
For molded marks the equivalent check is dimensional and visual: character height and stroke width measured on sintered parts, edges inspected for fill and flash, and the mark compared against a limit sample. Both routes converge on the same acceptance logic — define the criterion, define the sample, then measure against it.
Writing the Marking Requirement on the Drawing
Most marking disputes come from a drawing note that cannot be inspected. "Mark clearly" or "marked with part number" gives neither a location nor a criterion. A workable requirement states the mark content and format, the face and datum it is located from, the orientation, character height and stroke width (or states that they are quoted on request pending a tool trial), the durability required and the cleaning or sterilization cycles it must survive, and the inspection method with sample size.
For regulated products, direct marking is conditional rather than universal. Under 21 CFR 801.45, a device that must bear a UDI on its label and is intended for repeated use and reprocessing before each use must also carry a permanent mark on the device; the mark may be plain text, automatic identification and data capture, or another technology that provides the UDI on demand, and FDA lists etching, laser marking, plaques, and RFID among acceptable methods without mandating one. Permanence means demonstrated survival through the expected service life including reprocessing — not resistance to casual abrasion. Applicability, exceptions, and the choice of issuing-agency data structure are regulatory questions for the device labeler; Emitech marks to the drawing and the validated process, and does not act as regulatory filer.
Emitech runs ISO 9001:2015 quality control across a 0.1-200 g part range with as-sintered tolerances of ±0.3-0.5% of nominal dimension, tightened to about ±0.01 mm on sized or machined features, so a mark can be placed against a datum that actually holds. Tooling is typically 15-20 days from drawing approval and production 4-6 weeks after mold approval; whether marking is molded in, laser-applied, or both is decided in the DFM review, and part-specific character sizes, mark depths, and any dedicated marking fixture are quoted on request.
Frequently Asked Questions
Q: Can text and logos be molded directly into a MIM part?
Yes, through engraved or raised cavity geometry, but feasibility is set by feature size, aspect ratio, location, draft, tool steel, powder flow, sintering distortion, and inspection capability rather than by the font. Practical minimum character height and stroke width for a given alloy and part are established by a tool trial and quoted on request; a design rule pulled from a plastics guideline does not transfer.
Q: How is molded-in lettering compensated for shrinkage?
By scaling the glyph geometry and spacing with the same measured shrinkage factor used for the cavity, then verifying on sintered parts. There is no universal percentage: shrinkage varies with solids loading, debinding, sintering cycle, alloy, geometry, and orientation, so the factor has to come from measured parts rather than a rule of thumb. Where shrinkage is anisotropic, glyphs distort directionally and the mark is checked in both orientations.
Q: Is laser engraving better than molded marking for serial numbers?
For variable data, yes in most cases: serials, lot codes, dates, and 2D symbols change per unit or per batch, and laser marking absorbs that change in software while a molded mark would need a tool revision. For fixed logos or orientation arrows, molding them in usually removes an operation and a fixture. Many parts use both, with the laser field placed away from sealing and wear surfaces.
Q: What laser depth is needed for a permanent mark?
It depends on the durability requirement. Cited practice commonly specifies engraved depths in the approximate range of 0.01 mm to 0.10 mm, while annealing-type marks remove essentially no material and rely on surface contrast. Deeper is not automatically more durable: removal reduces section, concentrates stress, can trap contaminants, and may affect corrosion or fatigue behavior. The depth for a specific part and alloy is quoted on request and validated under the actual cleaning or sterilization cycle.
Q: When is molded-in or laser marking not recommended?
Molded-in marking is not recommended for variable data, for very small strokes in thick sections, or on sealing, mating, and fatigue-critical surfaces. Deep engraving is not recommended on thin walls or in corrosion-critical and cleanability-critical areas. Laser marking on a rough as-sintered surface may not deliver a machine-readable code without a finishing step, and direct UDI marking is not required on every component — applicability depends on device classification, labeling, intended use, and reprocessing.
Marking is one of the few part features that is decided once and then carried by every downstream step, so a mark that is too small, too deep, or in the wrong place is expensive to correct after the tool exists.
If you are specifying a part number, logo, serial field, or 2D code, send the drawing with the intended location and durability requirement through the contact page. Emitech reviews marking feasibility together with wall thickness, gate position, and tooling during the DFM review and returns a quotation within 24 hours.
Precision Metal Parts from Emitech
Nanjing Emitech delivers MIM, CNC machining, and custom metal parts. MIM services · Request a quote

